As stated, I'm looking for a shop near Elkton, MD to install a TeraFlex low range kit with JB Conversions twin stick in my 76 CJ-5. I know it's not a hard job, I just don't have the time to tackle it right now.
I DD the CJ, so time is of the essence. Thanks in advance!
Tires and rims or tires only? 4 or 5?
At this point with two respondents (including me) it's shaping up to be more of a date than a meet and greet. Since I have other obligations that day, I think I'm going to bow out.
I'd definitely be interested in a future event as proposed.
1. Me, cj8
2. Steve, Lovely (Can be there by 12, will have to bounce by 1:30)
On Saturday morning (day of the ride), is there a specific time and place to meet?
who is heading up Friday? I plan to roll out of N. Wilmington around noon to go set up camp.
I'm rolling out of Ceciltucky around 1 PM on Friday so we should be up there by dinner.
Lol. I really haven't driven it more than around the block a few times. I'm planning on going to get tags Sat morning. I want to take it to the membership trail ride on the 18th but I'm a little leary about driving it way up there.
Sent from my iPhone using Tapatalk
Looks great! I say...send it : )
I finally decided to tackle my new seat bracket install. Not being one to miss "leg day" and lack of tilt wheel in a CJ5, I needed to do something. I'm removing my bestop tilt brackets with sliders (they'll be for sale soon!) and replacing them with a non-tilt MUCH shorter bracket. I have a few holes to drill and it should be buttoned up in the next few days.
The club ride coming up has forced me to tackle some long over due projects!
Thanks guys!
Finally got around to finishing a 2.5" lift install on my 76 CJ5. Keeping this Jeep low and stock(ish). My plan is for this one to stay on 31s, be wheeled mildly and driven as often as possible.
Before and after. The clapped out 43 year old original springs were almost flat.
Began the installation of my heavy duty (greaseable) 3/4" shackles with a 2.5" Skyjacker lift. Got to love a 43 year old southwest Jeep. I didn't have to use my universal wrench (4" angle grinder) to remove a single nut or bolt!
I vote June 8th FWIW. I think you'd probably get a better turn out since a lot folks travel on Memorial Day weekend.
How does everyone / anyone feel about May 4th?
May the (4th) force be with you????????
That'd work for me. The sooner a date is chosen, the better chance I'll have in attending. The calendar fills up quick!
I like where your heads at kid. I'm very interested.
I think I replied to your PM. If not, please let me know...
Thanks
You did indeed reply. I shot you one back with my phone number. Probably make communication easier for both of us. Thanks and look forward to meeting you Saturday 
I have one, if you'd like to come get it.
PM sent.
1. Stafford black/blue camping dinner
2. Slowpoke black/blue dinner
3. Baldchris black/blue camping dinner site 154
4. Deadfeat blue/black camp+dinner
5. Dkirkley green/blue camp/dinner
6. Bee green/blue camp/dinner
7. Solomi +1 - reds / site 110 / dinner
8. JKGRAY10/ reds/ site 112/ I like food
9. AEZ
10. Stomper Blue /black/ Dinner
11. Astape - dinner and a movie
12. Lovely+1 - green (maiden voyage)/site 11/dinner
Replaced the 43 year old rear drive shaft u-joints after the catastrophic failure. While I was there I decided to change the t-clase fluid as well. Then of course the obligatory "test run" 
I've got one for $50, located in Linfield, PA 19468 or could bring to work in West Chester, PA (about 10 minutes or so from Quadratec). Looks OK from the front (has rust on the side that butts up against the one fender). Perfectly usable for a wall hanger.
Best case West Chester is still close to an hour from me. Since this is a want not a need, I will probably hold out for something a bit closer to home. If you are ever down in the North Eastern corner of Maryland, I'll take it.
Condition doesn't matter. Not looking to spend a fortune as this will be wall art for the man cave. Thanks!
