my 5speed 4.0 wrangler X had 3.03 gears
Posts by mellowyellow
-
-
they may have finally updated it. i used this one from raingler..it was dead on with my GPS
looks like quad updated their chart...sorry for the confusion
TJ Speedo Gear Chart
R&P / Tire 38" 37" 36" 35" 33" 32" 31" 30"
5.13 .. .. .. .. .. .. .. ..
4.88 36 37 38 39 41 43 44 46
4.56 34 35 36 37 39 40 42 43
4.11 31 32 33 34 36 37 38 40
3.73 27 28 28 29 31 32 33 34 -
dont follow the chart on quadratec...its not accurate. check other places online...i forget who i used but quadratec was off by a tooth or 2
-
on my way home from work today (3:30 ish) i passed a red avalanche towing a primer grey K-5....looks like he made the right choice (or has a twin) it was on RTE 41 just before RTE 10 in cochranville
-
-
those new front seats i see?? what did you do with the old ones...condition??
looks like you got in on the 49 dollar high lift special as well. ill have the 93 on the road soon...YJ's are taking over
-
2000 lbs.... the blazer weighs more than that??
the biggest problem with the tow rating isn't due to strength/power...its the weight to wheelbase ratio.. ive seen a guy with a wrangler pull a 19 foot boat out of a lake and it looked like a tractor pull (front tires in the air)......ok..i admit...it was me. i got it out..but i wouldnt say it is one of the better moments in my life.
last resort i would flat tow the blazer with the jeep, then go back for the trailer.
-
the sleeping bag was a nice touch.
-
i got a hi-lift that i had sitting behind jerry's cherokee for a little while while i looked around for a while.
-
what doesn't crutchfield sell now??
-
where do you guys fish in PA?? i make it up to the conowingo reservoir and lake aldred now and then....its been a while though
-
I was going to replace my valve cover gasket and was thinking do cover at the same time...no reason. Is there a reason you didnt want to replace the valve cover? Im leaking oil pout the back of the cover back by the fire wall. (?)i call the leaking valve cover corrosion prevention LOL just lazy thats all.
-
thanks john...found this for more information
http://www.autozone.com/az/cds…fe738/repairInfoPages.htm
time to play in the garage
-
so you are saying its just an elbow with the small hole in it. (what it looks like...figured the insides were shot).. it does have 2 lines (one large one small) going to the intake manifold area. guess i may not need one then. ill have to research this more so i understand the system. seems like the 93 was a test dummy for jeep LOL......cant wait to get things wrapped up so i can get on the trails again.
i miss the TJ...but i wont think twice about rolling the YJ
-
can anyone help me in my search of a PCV valve for the YJ. it isnt even listed in pep boys, advance, or auto zone's computer. the part numbers on the one the jeep has are gone. it is not like one i am used to seeing. does not slip into the grommet. it is more of a insert and twist setup i know this seems like one part everyone should have...but i cant find one.
i may just get a grommet and switch it over to one from a different 4.0...dont want to replace the valve cover though
-
out near Lancaster.
-
check with somewhere that installs car alarm systems. i have used them in alarm installs
-
If you strike out, you can try a beverage distributor, they use CO2 for kegs. Just a word of advice, if I were to do it again, I would not buy a CO2 bottle. Buy the regulator and equipment and stuff, but just swap the CO2 tank when it is empty for a new full one.i agree, places like keen you pay for the bottle once (100 bucks or so) but then you just swap it out instead of refilling. Keen dosent refill on site at most places so you have to wait a week....or you can just swap for a full one on the spot for like 15-20 bucks. also if you "OWN" your own tank you will have to go through a hydrotest and pressure checks at various intervals....not a worry when you trade
-
interesting..my light came on after 170 miles since my fillup.....if it dosent turn off tomorrow im going to scan it.
-
i agree with Joo...cindys in wilmington. she has done 3 cars for me and i have been more than happy with the outcome (and im picky).
may want to wait till the weather breaks though. it is better to have 2 or 3 days of good sun/heat to help it dry out.