Snap-On 40”Rolling Tool Box
Model: KRA4107A
Ball Bearing DrawerSlides
Drawer Liners
Currently Sells Newfor $2290.00
https://store.snapon.com/KRA4107-Heritage-Series-Roll-Cabs-40–40-7-Drawer-Single-Bank-Heritage-Series-Roll-Cab-P650741.aspx
Asking $1050
Both boxes have been sold
Thanks
Waterloo 40” tool chest has ball bearing slides and drawer liners
$120
US General 42” Roller cabinet has ball bearing slides and drawer liners
$320
Both for $360 OBO
Rather sell both as a set but will separate but top box must be sold first.
SOLD
Good to see some old Friends and meet some new ones 
1. Stafford (I don't think I can win plus I'll probably be organizing Schaefer's)
2. whatevah (managing poker run)
3. Kuntryboy816 + the whole fam damily 
- poker run
4.Skeets682 - poker run from the south
5.Blkrubi - poker run from the south
6. Captain II (I can help with set up just let me know)
7. Captain In for the Poker Run
8.Imarammr+1 poker run9. Slimer + who knows in for Poker Run and a beer or 2
10.Sandtostand plus 3 ( i'll be scoping out the local boat ramps, hoping to find a good one to ditch the jeep in the canal) pile of 
11. Keith.eric for the Poker Run
12. Grningbear + family - poker run
13. Quadna & Icky - both doing the poker run and coming up from the south.
14. YJDave & Maggie Poker run from the north
15. Shorebird and Sandy, poker run south if I'm not too late.
16. PacoPirate and the Mrs.(My home turf... have to make a cameo)
17. Yobob doing poker run coming from the north
18. tacklemom doing poker run - going to mix it up and make it an adventure (I also geocache, so I may pick up a cache or two I don't have yet)
19. Chief57 and Tess doing the poker run from the south
20. Subvet - maybe if jeep can make it - poker run North
Yo Fran!!! Great seeing you on here.
That was a crazy trip. Poor SLOPAR had a rough Big Dogs that year.
Convoys can be a pain in the ass, especially when they are mixes of trailers and Jeeps. I prefer mostly solo now...maybe one or two others max.
I havent gone anywhere, i have just been layin low and lurking around here the last few years with nothing much to say
Other that that minor hiccup the rest of the trip was good thought the trail took its toll that year
I met a guy called Subvet on here, he has a Cj2a with 35's. I told him he should take it up there that weekend but he said something about a convoy trailer accident one time. His jeep's not quite ready yet.
IIRC,
The Convoy was Knoxrents, Slopar, Jman, Alextremetj, Solomi, and myself, I think, we may have clogged up 95-695 
https://www.delawareja.com/for…20208.msg172035#msg172035
I have a pair (2) BFG AT 305/70/16
probably make good spares
take one or take both
You can just come get them or bring a six pack of Coors light would do 
Blast from the Past: RC 8-17-2008
Gonna try to get there +1
Need a Radiator for 2000 TJ
Anyone know off hand where is the best place to get one
TIA
I don't have an aftermarket bracket.
That was my question.
IC.
When you rotate your axle to the correct angle for the SYE you can see if the factory bracket will retain its alignment with the TB. if not then put the bracket in.
I believe the twisting of the stock bracket you are reading about is caused by the TB being misaligned with the stock bracket through its travel. (misalignment contributed by the axle rotated to meet the SYE angle).
I believe with a 3.5 lift you may be OK.
edit: OK confirmed by Ian while I was typing
I have the "standard" RE1603 bracket that has been used with 3.5 and 4.5 springs
and has worked fine so far. I installed my SYE sometime shortly after the 3.5 springs were in and before the 4.5 springs went in.
HTHs
Dont bolts treated with this stuff sometimes work themselves loose?
Never if torqued correctly
2000 Jeep Wrangler
4.0L with 3 speed Auto
B&M Tranny Cooler
RE 4.5 springs
RE lower control arms
RE adj rear uppers
stock front uppers
RE SS front brake lines
Black Diamond & RE bump stops
Currie Tie-rod & Drag Link
RE rear adj track bar
RE front adj. track bar
Bilstein 5150 shocks
35x12.50x15 MT MTZ’s mounted on AR Outlaw II
Cherokee HP Dana 30 3.73 gears open
Dana 44 3.73 gears with LSD
SYE
Tom Woods rear CV shaft
RE rear extended sway bar links
ORO Sway Loc Dual Rate Sway Bar
Rubicon Flares
Clayton Engine skid
Clayton Xfer case skid
Genrite Gas tank Skid
Poison Spider rocker guard
Custom nerfs
Mike Green lower control arm skids
OR-Fab tube doors
OR-Fab Sport cage
Poison Spider font Differential cover
Bestop Front bumper
Custom rear bumper with and tire carrier and Hi-Lift mount
Silver-star headlights
Fogs
Uniden 510 CB with Sirio Antenna
JVC head unit
5-1/4" speakers in the dash 6-1/2" in the sound pods
250w direct amp with 10” JL sub in custom box
Powertank CO2 Onboard air
Mile Marker winch
Couple of rigging shackles
hardtop First Aid kit
Dual chrome Fire Extinguishers on the cage
Fire extinguisher by the drivers seat
Stuff on the garage floor to be installed
D44 Disc Brakes
Clayton Long Arm
I have no regrets going to 35's.
Still like them, and still drive it on the road just about daily.
IMHO, Which ever size you decide on (33 or 35) do your axle first.
That little shack takes cards?I never even thought to try.
The Big Dogs registration is in a separate area so if you don't paypal, just bring your $75 in cash for them.
Yeah Billy, they even took cards the first time we were there
more advanced than you would have thought ;D
