Is it running with the new engine? How about some pictures?
Since you asked.
Hopefully by this weekend it will be running. Here are a few pics.
Is it running with the new engine? How about some pictures?
Since you asked.
Hopefully by this weekend it will be running. Here are a few pics.
Holy CRAP look at all those hoses! I assume there is an engine under there somewhere. It makes me appreciate my Jeeps OLD SCHOOL technology.
I hope you are doing a good write up with lots of pics.
I was trying to but when you in and start wrenching the camera is kind of out of site out of mind. All of those hoses were from the 2.5 not that there are any less with the 5.9L but it looks cleaner to me. Also you dont have to deal with combining three wiring harnesses which is a huge job in itself.
WOW the jeep has been reborn. Looks good
what tranny are you using???
I got an NV3550 hopefully it holds up.
the 3550 should hold up, from what i hear they can take up to 500hp. were you able to use the TJ instrument panel?
Thats the plan waiting to get the wiring harness back was a little more involved that I had time for had to combine the old engine harness, the new engine harness, and the wiring off of the firewall. Also had the PCM flashed because the 5.9L had an automatic behind it originally and now I am using a manual.
yeah i was thinking about throwing the 5.2 or 5.9 in place of my 97 2.5 but i wanted to use the tj I/P so instead i just got a 2002 4.0 and nv3550. just getting that wired up was a pain...
Excellent news Jason, keep us posted.
Got the wiring harness and the PCM in the JEEP. Trying to start it and I cant get it to turn over. I dont think its getting fuel. Does anyone know if the 5.9L requires a higher fuel pressure than the 2.5L?
i would have to guess so since if has twice the cylinders i mean i dont know for sure but that would be my guess.
i would have to guess so since if has twice the cylinders i mean i dont know for sure but that would be my guess.
No...you don't need more fuel pressure for more cylinders. Most modern EFI setups should be around 40-50 psi.
Does the fuel pump prime when you initially turn the key to run? Are you getting a signal from the crank position sensor? Are you getting any MIL's?...does the MIL light even illuminate for a couple seconds at key on to indicate functionality? Either backprobe at the injector or pick up a 'noid' light from pepboys/autozone/whatever for a couple bucks and see if the injectors are firing.
--Ian (done plenty of engine swaps in imports...)
what did you have done to the wiring harness? and are you talking about the engine harness from the 5.9 or the 2.5?
I cant tell if the fuel pump is priming i dont hear anything. The crank postion sensor is hanging off right now so that might be an issue forgot about that cant seem to find exactly where it mounts but then again I only looked for a sec. and yeah the check engine light comes on at key start then goes off. All of the gauges work gas, voltage, oil pressure. I have pressed in the pressure releif valve on the fuel rail and it doesnt seemed to be pressurized.
QuotePosted on: Today at 11:23:40 AMPosted by: ATRock
Insert Quote
what did you have done to the wiring harness? and are you talking about the engine harness from the 5.9 or the 2.5?
The 5.9l harness, the 2.5l harness and the wiring harness off of the firewall were combined together.
Check all of your grounds for the harness if they are not all hooked up you will not get any injector pulse . And when you say you cant get it to turn over do you mean it will not crank at all or do you mean it will not start .
I'd assume he meant it wouldn't start because he mentioned he wasn't getting gas.
I'd check the TPS as well as the grounds.
I was over there today, Seems to be a ground issue
he has 12v to the pump but the ground is interrupted.
Well traced the ground from the fuel pump to find out that the other end wasnt connected. Easy enough to fix. Now the fuel pump kicks in and I have fuel pressure but now there is no spark. All new wires, new plugs, cap and rotor were replaced also. I swapped the coil from my 2.5l engine with the 5.9l still no spark. Also tested the ASD relay it works fine. 20 amp fuse in that line is good also. Not sure what to do now. Any ideas?
Did you mount and hook up the crankshaft position sensor yet? You won't get any fire without that.
Don’t have an account yet? Register yourself now and be a part of our community!