You mean like the one in the bottom left corner of my windshield or is there another one?
What have you done to your Jeep today?
-
-
You mean like the one in the bottom left corner of my windshield or is there another one?
Yeah. That one. It looks reversed. -
I didnt want to stick it on the outside because it is not very tacky so I was afraid it would fly off. I am also a little worried that the new banner at the top will get scraped off by the wipers but, what are ya going to do?
-
I didnt want to stick it on the outside because it is not very tacky so I was afraid it would fly off. I am also a little worried that the new banner at the top will get scraped off by the wipers but, what are ya going to do?In 7 years I've never had a Member sticker come loose.
When it comes time to change them they are always still plenty stuck to the windshield.
-
Good to know.
-
Well Finally I completed my Scout Dana 44 rear axle install, Thanks Aaron for the welding! Installed with very few snags..
The hardest part was figuring out how to route the Scout parking brake cable.. Drivers side was easy but the pass side required 2 pulleys to get it to line up right with the CJ pedal cable. It actually works well ! Will post a few pics tomorrow.
Front axle next..
Steve
-
Drove the YJ to West Chester today. Inspection time ! 1st stop Emissions FAIL Bad cat so off to Quadratec. With new cat in hand I started the disassembly muffler/tailpipe off no problem. started to pull the cat off the head pipe and I find RUST and a HOLE :upset: .Call all the local part suppliers and Quadratec not available! Finally located one at NAPA in Downingtown but won't be in till 4pm. So the beast now sounds like a top fuel drag car and is stuck in W Chester till Thurs(work tomorrow) but she is nice and warm and dry in the shop. One good thing I am sure the cat was the problem( it was completely empty) and it did pass the safety inspection
-
Drove the YJ to West Chester today. Inspection time ! 1st stop Emissions FAIL Bad cat so off to Quadratec. With new cat in hand I started the disassembly muffler/tailpipe off no problem. started to pull the cat off the head pipe and I find RUST and a HOLE :upset: .Call all the local part suppliers and Quadratec not available! Finally located one at NAPA in Downingtown but won't be in till 4pm. So the beast now sounds like a top fuel drag car and is stuck in W Chester till Thurs(work tomorrow) but she is nice and warm and dry in the shop. One good thing I am sure the cat was the problem( it was completely empty) and it did pass the safety inspection
I recommend getting a front/head pipe from a TJ since they're routed differently and give you more clearance. I got hung up on a rock in rock creek with my YJ one and it cracked my manifold ...let me just say that was a LOUD 2 hour drive home haha -
Well my beast is up and running. Ems3420 and I worked on the wiring to tidy it up and make the engine bay all pretty. Then we deciced what the hell might as well throw the front clip back on it. Well any way it looks like a Jeep again after 4 months. Hope to be on the trail with it by April 24th. Just look fot the orange frame ya can't miss it!!!! LOL
-
Drove the YJ to West Chester today. Inspection time ! 1st stop Emissions FAIL Bad cat so off to Quadratec. With new cat in hand I started the disassembly muffler/tailpipe off no problem. started to pull the cat off the head pipe and I find RUST and a HOLE :upset: .Call all the local part suppliers and Quadratec not available! Finally located one at NAPA in Downingtown but won't be in till 4pm. So the beast now sounds like a top fuel drag car and is stuck in W Chester till Thurs(work tomorrow) but she is nice and warm and dry in the shop. One good thing I am sure the cat was the problem( it was completely empty) and it did pass the safety inspectionPercy I saw your Jeep this morning At Tragos(spell) when I was in The Dub C.
-
Percy I saw your Jeep this morning At Tragos(spell) when I was in The Dub C.
Yup I had to work today. I'll be putting it back togather tomorrow then run it down to DARE for the dyno retest
-
I recommend getting a front/head pipe from a TJ since they're routed differently and give you more clearance. I got hung up on a rock in rock creek with my YJ one and it cracked my manifold ...let me just say that was a LOUD 2 hour drive home hahaI'll remember that next time I found and bought a YJ pipe so that's what is goin on it now
-
Cleaned out half the garage that was full of D60 parts and tools I have been too lazy to put away, pulled the M101 out, all to be able to get the Jeep in and hoist the hard top off. ;D
-
Finished up my bumper/winch install.
-
Finished up my bumper/winch install.looking good, geoff. i promise that i'll get into a real good stuck at Big Dogs so you can get to use it!
-
Well painted the front end of the Cj last nite. Played taxi for percy to get his yj and more parts!!!! Going to try for the roll cage and rest of the wiring 2nite. Rewire the front end and install some Hella light upgrades.
-
Did this a bit ago but here are some pics of the new Wet Okole seat covers and sPod controls...
-
Installed my Rokmen gas tank skid today. Kinda a pain doing it alone but all in all it was a very easy project. Took about 1 hour. Definitely can see a large gain in clearance both to the ground and to the axle.
-
who makes those switches?
got a surf tag and added rod holders to the front bring on the fish
-
Switches are made by Carling. But the whole assembly is from SPOD. http://www.4x4s-pod.com/
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!